??互搏体育??

Service Hotline: 021-56728844 51693244 Click here to send me a message
??互搏体育?? page Company Profile Products News Center Leave message Applications Download Blog Center contact us
Category: reducer | gear reducer | stepless speed reducer | cycloid reducer | gear steering box | screw lifter | worm gear reducer | planetary reducer |
R series helical gear hard tooth surface reducer
S series cylindrical worm reducer
K series arc bevel gear hard tooth surface reducer
F series parallel shaft helical gear reducer
MB, MBN series planetary cone disc stepless speed changer
XBJXJ series cycloid reducer
WB series miniature cycloid reducer
G series single-phase three-phase gear reduction motor
Z series hard toothed cylindrical gear reducer
T series spiral bevel gear steering box
ARA series spiral bevel gear steering box
HD spiral bevel commutator
SWL worm gear screw lift
JWM screw lift
RV series worm reducer
WP cast iron worm gear reducer
PL series precision planetary reducer
PF precision planetary reducer
PS series precision planetary reducer
PW series precision planetary reducer
HB standard industrial gearbox
MC large gear reducer
CW circular arc cylindrical worm reducer
DBY / DCY series conical cylindrical gear reducer
The solution to the excessive heat of the cycloidal pinwheel reducer
次 Tag: Cycloidal pinwheel reducer Time: 2011/12/4 Click: 2815 times

The solution to the excessive heat of the cycloidal pinwheel reducer
To be a reducer technician, not only must have a wealth of knowledge and a large amount of experience in selecting a reasonable reducer, but also the ability to repair and deal with some common faults and uncommon problems of cycloidal pin gear reducers. Only by mastering this can you be a qualified reducer technician. There is no further discussion on the purchase of reducers, but this is not an aspect that can be ignored. Another aspect of reducer technology is that after the reducer is purchased, due to frequent use or excessive use, even when it is used in small amounts, there will be some problems, and these problems are not only for the theoretical knowledge of the technicians A practical assessment is also to examine the gearbox technician's ability to respond to unexpected problems. The following is a detailed explanation of some common problems of the reducer.
For an important member of the reducer family --- Cycloidal pinwheel reducer, sometimes it has such a problem that its temperature may be too high, and too high a temperature will cause many problems, not only affecting its The use efficiency can even damage the reducer in severe cases. This is a problem that needs everyone's attention. For its high temperature, we can analyze it from theory first, then draw conclusions, and finally give a solution. This is a common route to deal with emergency problems.
If the cycloid pin gear reducer is hot during use and the temperature is too high, in general, this may be a problem with the eccentric bearing and a failure. Of course, this is only a general situation, and other factors need to be considered, such as the newly purchased machine, there may be unreasonable assembly, or there may be problems. Of course, this knowledge is the reflection that must be formed in the mind after the temperature failure of the reducer is discovered, but this does not mean that the problem is due to this reason. For the temperature of the cycloid pin gear reducer, there may be another important factor to consider, which is the problem of lubricating oil. If the reducer lacks lubricating oil, the above problems may also be caused. This requires the right remedy and local conditions.
Of course, there are other reasons that need to be considered. If the cycloidal pin gear reducer is often overloaded, it may cause the temperature to be too high. However, these factors need to be analyzed and eliminated continuously to find the most correct answer. The reason why the temperature of the cycloidal pin gear reducer is too high has been found, and then there are solutions. There are many solutions to things, but the most direct and simplest, and the most reasonable should be the best method. This belongs to deceleration. The basic theory of machine technology will not be stated too much here.
In short, for the problem of excessive temperature of the cycloid reducer, find out the cause of it, such as the above-mentioned possibilities. If these reasons are ruled out, then look for other factors that may affect the temperature of the reducer. Then give the right solution, give a solution, and implement it. If you do this, you will be able to handle the failure of the reducer easily.


Close this page 】 【 Print this page
Previous: Principle of Cycloidal Pinwheel Reducer Next: What are the main characteristics of the cycloidal pinwheel reducer
Copyright ? 2009-2012 Shanghai Yijie Transmission Machinery Co., Ltd. <br /> Address: Pudu Industrial Park, Xidu, Fengxian District, Shanghai Postcode: 201401
Shanghai ICP No. 11041404
七乐彩 欢乐拼三张 真人游戏平台注册 欢乐拼三张